The Bryant Plus 90 Furnace is a great device, but like all electronics, it sometimes has its issues. If your Bryant Plus 90 Furnace is not working, take a look at this troubleshooting guide.
We’ve collected answers to the most frequent reasons you’ll see Bryant Plus 90 Furnace not working and explained them in plain language for easy troubleshooting.
Quick Fix
To troubleshoot a Bryant Plus 90 Furnace, check the thermostat and power supply, ensure the air filter is clean, inspect the vent for blockages, and reset the furnace by turning it off and back on after a few minutes.
Pre-Troubleshooting Checklist
Before diving into troubleshooting your Bryant Plus 90 furnace, go through this pre-troubleshooting checklist to verify you’ve covered the basics.
First, confirm your thermostat is set correctly – check the thermostat setting to guarantee it’s calling for heat.
Next, verify the furnace filter is clean and not clogged, as a dirty filter can reduce airflow and cause issues.
Check the circuit breaker or fuse box to guarantee the breaker hasn’t tripped or a fuse hasn’t blown, which would prevent the furnace from operating.
Inspect the return air grilles and supply air registers to guarantee they’re not blocked or restricted, as this can impede airflow and cause problems.
Confirm the blower motor is working properly and not making unusual noises.
If you’ve checked all these items and the issue persists, it’s likely a more complex problem with your Bryant Plus 90 gas furnace.
At this point, you can begin troubleshooting more specific issues with your HVAC system.
Common Issues and Solutions
Several common issues can arise with your Bryant Plus 90 gas furnace, and being aware of these problems and their solutions can help you troubleshoot and resolve them efficiently.
For instance, if your furnace is blowing cold air throughout, it may be due to dirty filters, which can reduce furnace efficiency. Replacing the filter monthly or bi-monthly can maintain peak performance.
Inadequate heating can also be caused by a faulty igniter, which can prevent the furnace from firing. Cleaning or replacing the igniter can resolve the issue. Additionally, verify the thermostat is set correctly, and check the circuit breakers to confirm they haven’t tripped.
A faulty rollout sensor can cause the furnace to shut down, but resetting the rollout switch near the burner section can resolve the issue.
Regular maintenance, such as guaranteeing the condensate drain pipes are clear and levelled, can also prevent common issues. By being proactive and addressing these common issues, you can minimize the need for furnace repair and guarantee your Bryant Plus 90 furnace Model operates effectively.
Error Codes and Faults
When you’re troubleshooting your Bryant Plus 90 furnace, error codes and faults are essential indicators of what’s gone wrong.
You’ll need to identify the specific fault code displayed on the furnace’s control board to determine the root cause of the issue. By understanding the error codes, you can diagnose issues like the Flame Rollout Fault and take corrective action to get your furnace up and running again.
Flame Rollout Fault
Your Bryant Plus 90 furnace displays a flame rollout fault when it detects an abnormal flame pattern or rollout condition, which can be triggered by a variety of factors.
This fault can cause your furnace to stop coming on, leaving you without heat. A flame rollout fault typically occurs when the inducer motor or ignitor malfunctions, causing the flame to roll out of the combustion chamber.
This can be due to a faulty circuit or thermostat issue.
When troubleshooting a flame rollout fault, you’ll need to inspect the furnace’s combustion chamber and burner assembly.
Check for signs of soot or debris buildup, which can obstruct the flame’s normal pattern. Verify the ignitor is functioning correctly and the inducer motor is operating within the specified RPM range.
If you suspect a thermostat issue, try replacing the thermostat to see if it resolves the problem.
Remember to always follow proper safety procedures when working with gas furnaces, and consider consulting a professional if you’re unsure about any aspect of the troubleshooting process.
Error Code Diagnosis
The Bryant Plus 90 furnace’s error code diagnosis is a crucial step in identifying and resolving issues that may be preventing your furnace from functioning properly.
When your furnace displays an error code, it’s essential to diagnose the problem accurately to perform the necessary repairs.
You can find the error code on your thermostat’s display or in the furnace’s control panel.
Once you have the code, consult your user manual or online resources to determine the cause of the issue.
- Error Code 12: This code indicates an ignition problem, which may be due to a faulty igniter, a dirty air filter, or a malfunctioning gas valve.
- Error Code 31: This code suggests a furnace not firing issue, potentially caused by a faulty thermostat, a blocked air filter, or a faulty furnace control board.
- Error Code 44: This code points to a heating system problem, possibly due to a faulty furnace limit switch, a malfunctioning gas valve, or a blocked air filter.
Furnace Maintenance Essentials
You’ll want to focus on three key areas to guarantee your Bryant Plus 90 furnace runs efficiently and trouble-free: regular filter cleaning, condensate drain maintenance, and proper thermostat settings.
Regular Filter Cleaning
Regular filter cleaning is a crucial aspect of furnace maintenance, as it directly impacts the system’s performance and longevity.
A dirty filter can lead to reduced airflow, causing your Bryant Plus 90 furnace to work harder and increasing your energy bills.
This can also result in cold spots in your home, making it less comfortable.
To safeguard your furnace is running efficiently, you should clean or replace the filter every 1-3 months, depending on usage and environmental conditions.
- Turn off the power: Switch off the furnace’s power supply to prevent any accidental start-ups while you’re cleaning the filter.
- Remove the filter: Take out the filter from the furnace and gently tap it to remove any loose dirt or debris.
- Clean or replace: Clean the filter with a soft brush or vacuum, or replace it with a new one if it’s damaged or excessively dirty.
Condensate Drain Maintenance
One essential aspect of maintaining your Bryant Plus 90 furnace is condensate drain maintenance, which involves verifying the condensate drain system functions properly to prevent water accumulation and related issues.
You should regularly clean the condensate drain hoses to prevent clogs and water accumulation. A clogged drain hose can cause water to accumulate in the furnace, leading to corrosion and damage to components.
Additionally, inspect and clean the p-trap and drain regularly to prevent blockages. Improper furnace installation or maintenance can also contribute to water accumulation, so confirm your furnace is installed and maintained correctly.
Failure to clean the condensate drain hoses regularly can lead to clogs and water accumulation, causing the furnace to shut down. Regular maintenance is pivotal to prevent such issues and verify your HVAC system operates efficiently.
Proper Thermostat Settings
Maintaining ideal thermostat settings is vital to guarantee your Bryant Plus 90 furnace operates efficiently and effectively.
You should program your thermostat to maintain a consistent temperature, usually between 68°F and 72°F, to optimize your furnace’s performance. This setting also helps reduce energy consumption and saves you money on your energy bills.
To guarantee proper thermostat settings:
- Check thermostat compatibility: Verify your thermostat is compatible with your Bryant Plus 90 gas furnace. If you’re unsure, consult with an HVAC contractor or the manufacturer’s instructions.
- Set the correct temperature range: Program your thermostat to maintain a consistent temperature range, avoiding extreme temperature fluctuations that can affect your furnace’s performance.
- Regularly inspect air filters: Dirty air filters can reduce airflow, causing your furnace to work harder and increasing energy consumption. Replace your air filters, such as pleated filters, every 1-3 months or as recommended by the manufacturer.
Remember to also check your electrical panel and verify it’s functioning correctly. If you’re still experiencing issues, consider upgrading to a smart thermostat like the Nest thermostat for better control and monitoring.
Troubleshooting Steps and Tips
Several factors can trigger issues with your Bryant Plus 90 furnace, and pinpointing the root cause is essential to effective troubleshooting.
When your furnace won’t cycle, won’t fire, or is working but blowing cold air, it’s pivotal to methodically eliminate potential causes.
Start by checking the thermostat settings, validating they’re set correctly and the battery isn’t dead. Next, inspect the switch and motor for signs of wear or malfunction.
If your Bryant 350MAV036080adka plus furnace has a faulty switch or motor, it may not function properly.
Verify that the gas supply is turned on and the valve is open.
Certify the furnace filter is clean, as a clogged filter can prevent proper airflow.
Check the furnace’s electrical connections and wiring for damage or corrosion.
If you’ve checked all these potential causes and the issue persists, it may be time to weigh professional repair.
Remember, a properly functioning Gas Furnace is pivotal for your home’s comfort and safety.
Bryant Furnace Repair Guide
As you’ve methodically ruled out potential causes for your Bryant Plus 90 furnace issue, it’s time to consult the Bryant Furnace Repair Guide for more in-depth guidance.
This comprehensive resource provides troubleshooting tips and solutions for common Plus 90 furnace problems. Before attempting any repairs, remember to turn off the furnace to guarantee your safety.
The guide covers basic maintenance tasks and troubleshooting tips for issues such as:
- Faulty circuit breakers: Check if the breaker has tripped or if there’s an electrical issue.
- Malfunctioning thermostats: Certify the thermostat is set correctly and functioning properly.
- Faulty blower motors or broken connecting belts: Inspect the blower motor and belts for signs of wear or damage.
Professional Assistance and Warranty
If you’ve exhausted the troubleshooting steps outlined in the Bryant Furnace Repair Guide and the issue persists, it’s likely time to contemplate seeking professional assistance from a qualified HVAC technician who can diagnose and repair your Bryant Plus 90 furnace.
A licensed technician from HVAC at Johnson Controls or a similar service provider can help identify the root cause of the problem and perform the necessary repairs. Before scheduling a service call, review your furnace warranty to see if repairs or replacements are covered.
Bryant furnaces have a 10-year standard parts limited warranty if registered within 90 days of installation, and unregistered furnaces are still covered for five years. Be sure to keep a record of maintenance and repairs for future reference, as this may be required for warranty claims or to troubleshoot recurring issues.
Regular maintenance schedules can help prevent future issues and guarantee the furnace operates efficiently and safely.
Frequently Asked Questions
Where Is the Reset Button on a Bryant Furnace?
You’ll typically find the reset button on your furnace’s circuit board, often hidden behind a removable panel or accessed through a small opening; check your model’s wiring diagram or manual for specific location and button color code details.
Why Is My Bryant Furnace Not Working?
Your furnace has gone dark, leaving you shivering in the cold. Don’t worry, it’s likely due to a faulty ignition, clogged filters, dirty sensors, or one of several other common issues like incorrect installation, insufficient power, leaky ducts, or poor maintenance.
Why Does My Bryant Plus 90 Furnace Keep Shutting Off?
You’re experiencing furnace issues where it keeps shutting off, which could be due to overheating concerns triggered by faulty sensors, ignition problems, electrical glitches, or thermostat malfunctions, so investigate these potential causes to resolve the issue.
What Is the Most Common Furnace Failure?
As you navigate the dark alleys of furnace failures, you’ll find that sensor malfunctions, often symbolized by a dimly lit LED, are the most common culprit, followed closely by electrical faults, clogged filters, and pilot issues, all of which can lead to your furnace’s demise.
Conclusion
By following the troubleshooting steps and tips outlined, you’ve taken the first vital steps in resolving common issues with your Bryant Plus 90 Furnace. Remember, regular maintenance is key to preventing future problems, so commit to routine filter changes, blower motor checks, and electrical panel inspections. Stay vigilant, and you’ll enjoy a warm and cozy home all winter long, with a furnace that runs efficiently, reliably, and safely.
Table of Contents
